User ManualTable of ContentsChapter 1: Overview91.1 About the Transport GT24 B289191.2 Product Models101.3 Features111.4 Unpacking13Mainboard Manual141.5 About the Product151.5.1 System Front View15CD-ROM Drive151.5.2 System Rear View15Power Supply Socket151.5.3 LED Definition161.5.4 System Internal View - B2891G24S4H181.5.5 Motherboard Layout211.5.6 Motherboard Block Diagram23Chapter 2: Setting Up92.0.1 Before You Begin252.0.2 Work Area252.0.3 Tools252.0.4 Precautions262.1 Rack Mounting272.1.1 Installing the Server in a Rack271. Screw the mounting ear to each side of Transport GT24 as shown using 2 screws from the supplied screws kit.272. Screw the sliding rail brackets to the sliding rails.283. Slide the sliding rail to each side of the Transport GT24.284. Screw the sliding rail to each side using 2 screws as shown.285. Locate the mounting bracket from the supplied kit and screw it to the rack using 2 screws on each side. Be careful that the m...296. Lift and insert the unit into place in the rack (A). Ensure the unit is completely inserted into the rack (B). Then screw the unit into place as shown (C).302.2 Installing Motherboard Components312.2.1 Removing the Chassis Cover311. Release the screw on the back side. Then slide the chassis cover in the direction of arrow.312. Lift the cover off.312.2.2 Installing the CPU, Heatsink and Air Duct321. After removing the pre-installed air duct, locate the CPU sockets.32CPU socket322. Pull the CPU lever up to unlock the CPU socket.323. Place the CPU in the CPU socket, ensuring that pin 1 is located as shown in the following illustration.334. Press the CPU socket lever down in the direction shown to secure the CPU.335. Align the heatsink screw holes with the holes on the motherboard and insert two heatsink screws as shown.346. Replace the air duct over the heatsink and secure it to the motherboard using two screws.342.2.3 Installing the Memory351. Locate the memory slots on the motherboard.35Memory Slots352. Press the memory slot locking levers in the direction of the arrows as shown in the following illustration.353. Align the memory module with the slot. The module has indentations that align with notches in the slots.354. Insert the memory module into the slot as shown.362.2.4 Installing a PCI Card361. Push the tab of PCI slot on the rear panel in the direction as shown to release the bracket.362. Move the bracket to left as shown.373. Insert the PCI-E card as shown.374. Push the tab of PCI slot in the direction as shown to fix PCI-E card.372.3 Installing the Hard Drive for B2891G24S4H/B2891G24U4H381. Press the locking lever latch in the direction of arrow (A) and then pull the locking lever open (B).382. Slide the drive tray out.383. Place a hard drive into the drive tray.384. Using 4 HDD screws to secure the HDD.395. Reinsert the drive tray into the chassis (A), ensuring that the drive tray is completely inserted into the chassis (B).396. Pressing the locking lever to secure the hard drive tray.392.4 Installing the Hard Drive for B2891G24S4-LC401. Remove the screw to release the hard drive tray.402. Slide the drive tray out.403. Place a hard drive into the drive tray and then secure the hard drive using 4 screws.404. Insert the hard drive tray into the bay.415. Reinsert the HDD data and power cable.416. Secure the HDD using a screw.412.5 Installing the Slim FDD (Option)421. Locate the two FDD rails and screws from the FDD kit. Secure the two rails to FDD using four screws.422. Connect the FDD backplane to FDD using 2 screws.423. Connect the FFC cable to FDD.424. Using a screw driver to pull open the door of FDD tray.425. Insert FDD module into the tray.436. Locate the FDD cable from FDD kit. Connect the wrinkle side to the connector on floppy slot. Refer to the picture below for the correct direction. Then, connect the power cable of FDD to the connector on floppy slot.437. Connect the other side to the connector on motherboard.43Chapter 3: Replacing Pre-Installed Components93.1 Introduction453.1.1 Work Area453.1.2 Tools453.1.3 Precautions463.2 Disassembly Flowchart473.3 Removing the Cover481. Release the screw and then slide the cover in the direction of arrow.482. Lift the cover in the direction of arrow (A).483.4 Replacing Motherboard Components493.4.1 Disconnecting All Motherboard Cables491. Disconnect ATX power cables492. Disconnect CD-ROM drive cable and SATA (or SCSI) hard drive cables.493. Disconnect the front panel, USB, and two LAN connectors. Refer to the mainboard layout for the locations504. Disconnect all fan power cables.503.4.2 Removing the Motherboard511. Remove the eleven screws securing the motherboard to the chassis.512. Remove the motherboard.513.5 Replacing the Slim CD-ROM521. Remove the power and data cables from the slim CD- ROM adapter.522. Press the latch in the direction as show to release the CD-ROM drive.523. The CD-ROM drive will be freed from the drive bay after pressing the latch.534. Remove the two screws that secure the CD-ROM drive to the bracket.535. Replace the CD-ROM drive.536. Use the two screws to secure the CD-ROM to the bracket. Then replace the unit into the drive bay and connect the CD-ROM power and data cables.533.6 Replacing the LED Control Board541. Remove the 2 screws securing the LED control board to the chassis.542. Pull the LED control board free from the chassis as shown below.543. Unplug the front panel ribbon cable from the connector.544. Unplug the USB cable from the connector.555. Remove the three screws securing the LED control board to the bracket556. Release the LED control board from the chassis. After replacement, insert and secure the unit to the chassis following the reverse procedures from step 1~5.553.7 Replacing the M1010 Adapter Board561. Remove all the cables connected to the adapter board, including front panel, USB, LAN, power and five fan cables.562. Remove the five screws to release the adapter board. Refer to page 47 for the locations..563.7.1 M1010 Adapter Board Features573.7.2 System Fan Layout583.7.3 M1010 Adapter Board Connector Pin Definition603.8 Replacing the SATA or SCSI Backplane651. Remove the 3 screws securing the adapter board to the chassis.652. Grab the two lables to lift the adapter board.653. Remove the ten screws that secure the bracket to the adapter board.664. Release the adapter board free from the bracket.665. Replace the unit to the chassis following the reverse procedures from step 1 to 4 after done.663.8.1 S-ATA Backplane (M1204) Features673.8.2 SCSI Backplane (M1205) Features703.9 Replacing the Power Supply741. Remove the two screws that secure the power supply to the chassis.742. Remove the screw that secure the fan assembly to the chassis74Appendix I: BIOS Differences75Appendix II: Cable Connection Tables77Table 1: B2891G24S4H Model77Table 2: B2891G24S4-LC Model77Table 3: B2891G24U4H77Table 4: System Fan to M1010 Adapter Board77Table 5: M1010 Adapter Board to Motherboard78Table 6: Power Supply to Motherboard78Table 7: Power Supply to M1010 Adapter Board78Table 8: Power Supply to M1204/M1205 HDD Backplane78Table 9: M1010 Adapter Board to Motherboard79Table 10: M1003 Front Panel Control Board Related Cable79Table 11: CD-ROM Related Cable79Table 12: Chassis Intrusion Cable79Table 13: FDD Related Cable (Option)79Technical Support80Size: 6.93 MBPages: 82Language: EnglishOpen manual