Information Guide (1658686-4)Table of Contents1. INTRODUCTION1This instruction sheet covers the use of Insertion/ Extraction Tool 91285-1 and Replacement Tip Kits 543382 shown in Figure 1. The tool is designed to insert and extract HD-22 and HD-20 contacts used in AMPLIMITE* High Density (HD) Connectors.1For information concerning the assembly of AMPLIMITE HD connectors, refer to the instruction sheet packaged with the connector.1Read these instructions thoroughly before using the tool.1See Section 6, REVISION SUMMARY, for revision information.12. DESCRIPTION (Figure 1)1The insertion/extraction tool consists of a handle, a cap, six insertion/extraction tips, a plug, and a [.050 in.] hex wrench. The handle of the tool provides storage for the tips, plug, and hex wrench. The insertion/extraction tips convert the tool ...13. TOOL ASSEMBLY (Figure 2)2Refer to Figure 1 and select the appropriate contact, wire size, and insertion/extraction tip. Proceed as follows:21. Insert plug into the widest end of the insertion/ extraction tip.22. Slide the insertion/extraction tip into the end of the tool handle with the orientation latch positioned toward the bottom of the tool.23. Using the hex wrench, tighten the setscrew to secure the tip in the tool handle.24. INSERTION/EXTRACTION PROCEDURES24.1. Inserting A Wire Crimped Contact (Figure 3)21. Position tool handle between thumb and fingertips, then place wire over the wire slot of the tip. Hold wire in this position with your thumb.22. Slide thumb over the wire toward the end of the tip.33. Slide tip over contact wire barrel until the tip butts against the contact shoulder.34. Align contact with the BACK of the contact cavity. Push contact straight into the contact cavity until the contact bottoms.35. Remove the insertion tool; then pull back on the wire to ensure that the contact is locked into the contact cavity.34.2. Extracting A Wire Crimped Contact (Figure 4)31. Position tool handle between thumb and fingertips, and align contact wire with the wire slot on the tip. Hold wire in this position with your thumb.32. Slide your thumb over the wire toward the end of the insertion tip.33. Place tip over the contact post or crimp barrel and slide the tip straight into the contact cavity until the tip bottoms against the contact shoulder.34. Holding the wire tight against the tool handle, pull back on the tool handle to extract the contact. If you experience difficulty in extracting the contact, repeat Steps 1 through 4.34.3. Inserting A Posted Contact (Figure 5)31. Place the contact in the contact cavity. Do NOT push on the contact post.32. Position the tip over the contact post. Move the tool along the post until the tip butts against the contact stabilizer. Align the tip on the stabilizer as shown in Figure 5.33. Hold the tool handle, and push the contact post to make certain that the contact is locked in the cavity.34.4. Extracting A Posted Contact (Figure 6)41. Place the extraction tip over the contact post. Move the tool along the post until the tip enters the contact cavity.42. Align the groove of the extraction tip with the contact stabilizer as shown in Figure 6.43. Push the tip past the stabilizer and straight into the cavity until it bottoms.44. For a receptacle style connector, insert a 1.02 mm [.040 in.] diameter pin straight into the FRONT of the contact cavity. For a plug style connector, push on mating tip of contact with a suitable device.45. Apply pressure to remove the contact and tool from the contact cavity.45. TOOL INSPECTION/REPLACEMENT (Figure 7)4Insertion/Extraction Tool is inspected before shipment. TE recommends that the tool be inspected immediately upon its arrival to ensure that the tool has not been damaged during shipment, and that the tool conforms to the dimensions provided in Figur...4For tool repair service, please contact an TE Representative at 1-800-526-5136.46. REVISION SUMMARY4Since the previous release, the last line of Figure 1 was corrected to indicate contact HD-22.4408-94041Size: 344 KBPages: 6Language: EnglishOpen manual
Information Guide (1658686-2)Table of Contents1. INTRODUCTION1This instruction sheet covers the use of Insertion/ Extraction Tool 91285-1 and Replacement Tip Kits 543382 shown in Figure 1. The tool is designed to insert and extract HD-22 and HD-20 contacts used in AMPLIMITE* High Density (HD) Connectors.1For information concerning the assembly of AMPLIMITE HD connectors, refer to the instruction sheet packaged with the connector.1Read these instructions thoroughly before using the tool.1See Section 6, REVISION SUMMARY, for revision information.12. DESCRIPTION (Figure 1)1The insertion/extraction tool consists of a handle, a cap, six insertion/extraction tips, a plug, and a [.050 in.] hex wrench. The handle of the tool provides storage for the tips, plug, and hex wrench. The insertion/extraction tips convert the tool ...13. TOOL ASSEMBLY (Figure 2)2Refer to Figure 1 and select the appropriate contact, wire size, and insertion/extraction tip. Proceed as follows:21. Insert plug into the widest end of the insertion/ extraction tip.22. Slide the insertion/extraction tip into the end of the tool handle with the orientation latch positioned toward the bottom of the tool.23. Using the hex wrench, tighten the setscrew to secure the tip in the tool handle.24. INSERTION/EXTRACTION PROCEDURES24.1. Inserting A Wire Crimped Contact (Figure 3)21. Position tool handle between thumb and fingertips, then place wire over the wire slot of the tip. Hold wire in this position with your thumb.22. Slide thumb over the wire toward the end of the tip.33. Slide tip over contact wire barrel until the tip butts against the contact shoulder.34. Align contact with the BACK of the contact cavity. Push contact straight into the contact cavity until the contact bottoms.35. Remove the insertion tool; then pull back on the wire to ensure that the contact is locked into the contact cavity.34.2. Extracting A Wire Crimped Contact (Figure 4)31. Position tool handle between thumb and fingertips, and align contact wire with the wire slot on the tip. Hold wire in this position with your thumb.32. Slide your thumb over the wire toward the end of the insertion tip.33. Place tip over the contact post or crimp barrel and slide the tip straight into the contact cavity until the tip bottoms against the contact shoulder.34. Holding the wire tight against the tool handle, pull back on the tool handle to extract the contact. If you experience difficulty in extracting the contact, repeat Steps 1 through 4.34.3. Inserting A Posted Contact (Figure 5)31. Place the contact in the contact cavity. Do NOT push on the contact post.32. Position the tip over the contact post. Move the tool along the post until the tip butts against the contact stabilizer. Align the tip on the stabilizer as shown in Figure 5.33. Hold the tool handle, and push the contact post to make certain that the contact is locked in the cavity.34.4. Extracting A Posted Contact (Figure 6)41. Place the extraction tip over the contact post. Move the tool along the post until the tip enters the contact cavity.42. Align the groove of the extraction tip with the contact stabilizer as shown in Figure 6.43. Push the tip past the stabilizer and straight into the cavity until it bottoms.44. For a receptacle style connector, insert a 1.02 mm [.040 in.] diameter pin straight into the FRONT of the contact cavity. For a plug style connector, push on mating tip of contact with a suitable device.45. Apply pressure to remove the contact and tool from the contact cavity.45. TOOL INSPECTION/REPLACEMENT (Figure 7)4Insertion/Extraction Tool is inspected before shipment. TE recommends that the tool be inspected immediately upon its arrival to ensure that the tool has not been damaged during shipment, and that the tool conforms to the dimensions provided in Figur...4For tool repair service, please contact an TE Representative at 1-800-526-5136.46. REVISION SUMMARY4Since the previous release, the last line of Figure 1 was corrected to indicate contact HD-22.4408-94041Size: 344 KBPages: 6Language: EnglishOpen manual
