User ManualTable of ContentsTable of Contents17Safety Instructions For Jointer/Planer17Safety Instructions For Jointer/Planer (continued)1Safety Labels and Indicators on the Jointer/Planer11. Safety instruction label on the top of the guard.12. Cutter rotation indicator is on top of the fence holder.13. Cutter position indicator is on top of the fence.14. Safety instruction label below dust chute.1When Installing Or Moving the Jointer/Planer1Before Each Use1To Reduce the Risk of Injury From Jams, Slips Or Thrown Pieces (Kickbacks Or Throwbacks)1Plan Ahead To Protect Your Eyes, Hands, Face and Ears1Inspect Your Workpiece1Assembly1Cabinet and Motor Mount Assembly11. From the hardware pack find the following:12. Mount the motor mount onto the left side panel as shown. Make sure the lower tab of the motor mount with two holes is on the ...13. Mount the right side panel to the motor mount as shown using two 5/16 carriage head bolts and 5/16 serrated flange nuts. Tighten the nuts with a wrench.14. From the hardware pack find the following:15. Bolt the front panel in place as shown using six 5/16 carriage head bolts and six 5/16 serrated flange nuts. Make sure the fr...16. Tighten all bolts on the base at this time.1Mounting Jointer Table to Cabinet181. With help place the bed assembly upside down on two blocks as shown.182. Place the jointer cabinet on top of the bed assembly as shown.183. From the hardware pack find the following:184. Bolt the table to the cabinet using the 3 hex head bolts and tighten all three bolts. To access third bolt, reach into dust collection port on left side.185. Slip the belt over both the motor and cutterhead pulleys.18Tensioning Belt and Installing Rear Panel181. While the jointer is still upside down slide the motor up the motor mount to put tension on the belt. This will require assis...182. Visually check the front to back alignment of the pulleys and adjust the motor as needed.183. From the hardware pack locate the following:184. Position the rear panel in place from the bottom of the cabinet as shown. Bolt in place using the six 5/16 carriage head bolts and six 5/16 flange nuts. Make sure the rear panel is on the inside of the cabinet side. Tighten the nuts.185. Thread the power cord through the hole in the rear of the cabinet.18Attach Sawdust Chute11. From among the loose parts find the following:12. Slide the tab on the bottom side of the dust chute into the slot just below the chute on the left side of the base. Fasten the dust chute on with the 2 wing screws through the slots on both sides of the dust chute.13. The 3mm hex-L wrench and 8mm open end wrench (supplied with the jointer) used for blade adjustments, can be conveniently stored in the dust chute as shown.1Adjusting Table Extension11. Loosen the 2 hex head screws that attach the extension to the outfeed table.12. Using a straight edge, align the extension to be flush with the outfeed table.13. Tighten the two screws and recheck the alignment.1Assembly (continued)1Assemble Fence To Bed11. From the hardware pack find the following:12. Position fence onto fence support as shown making sure the keyway in fence assembly lines up with the key on the fence mount.13. Once fence is in place, slide the fence lock knob through the 1/2" washer and then through the fence assembly and fence mount. Thread T-nut onto the end of the lock knob. Make sure the tabs on the nut sit in the slot on the fence mount.14. Slide the fence back and fourth to make sure it moves freely. Then lock in place.15. Thread the fence tilt knob into the fence.1Install Cutter Head Guard11. From among the loose parts find the cutter head guard. Remove the pan head screw from the bottom of the guard post.12. Turn the spring-loaded knob 1 turn counterclockwise, looking down through the hole in the infeed table.13. Line the slot in the guard post with the pin in the knob. Slide the post through table and over pin in the knob.14. Reinstall the pan head screw in the bottom of the guard post.1Getting to Know Your Jointer/Planer20Alignments22Alignments (continued)24Alignments (continued)26Safety Instructions for Basic Jointer/Planer Operation26Safety Instructions for Basic Jointer/Planer Operation (continued)28Basic Jointer/Planer Cutting Operations29Basic Jointer/Planer Cutting Operations (continued)30Basic Jointer/Planer Cutting Operations (continued)32Maintenance and Lubrication33Wiring Diagram33Repair Parts1Repair Parts1Repair Parts1Repair Parts1Table of Contents17Safety Instructions For Jointer/Planer17Safety Instructions For Jointer/Planer (continued)11. Safety instruction label on the top of the guard.12. Cutter rotation indicator is on top of the fence holder.13. Cutter position indicator is on top of the fence.14. Safety instruction label below dust chute.1Assembly11. From the hardware pack find the following:12. Mount the motor mount onto the left side panel as shown. Make sure the lower tab of the motor mount with two holes is on the ...13. Mount the right side panel to the motor mount as shown using two 5/16 carriage head bolts and 5/16 serrated flange nuts. Tighten the nuts with a wrench.14. From the hardware pack find the following:15. Bolt the front panel in place as shown using six 5/16 carriage head bolts and six 5/16 serrated flange nuts. Make sure the fr...16. Tighten all bolts on the base at this time.15. Using the two 3/16 screws, mount the switch into place as shown. Make sure the switch is right side up.141. With help place the bed assembly upside down on two blocks as shown.182. Place the jointer cabinet on top of the bed assembly as shown.183. From the hardware pack find the following:184. Bolt the table to the cabinet using the 3 hex head bolts and tighten all three bolts. To access third bolt, reach into dust collection port on left side.185. Slip the belt over both the motor and cutterhead pulleys.181. While the jointer is still upside down slide the motor up the motor mount to put tension on the belt. This will require assis...182. Visually check the front to back alignment of the pulleys and adjust the motor as needed.183. From the hardware pack locate the following:184. Position the rear panel in place from the bottom of the cabinet as shown. Bolt in place using the six 5/16 carriage head bolts and six 5/16 flange nuts. Make sure the rear panel is on the inside of the cabinet side. Tighten the nuts.185. Thread the power cord through the hole in the rear of the cabinet.181. From among the loose parts find the following:12. Slide the tab on the bottom side of the dust chute into the slot just below the chute on the left side of the base. Fasten the dust chute on with the 2 wing screws through the slots on both sides of the dust chute.13. The 3mm hex-L wrench and 8mm open end wrench (supplied with the jointer) used for blade adjustments, can be conveniently stored in the dust chute as shown.11. Loosen the 2 hex head screws that attach the extension to the outfeed table.12. Using a straight edge, align the extension to be flush with the outfeed table.13. Tighten the two screws and recheck the alignment.1Assembly (continued)11. From the hardware pack find the following:12. Position fence onto fence support as shown making sure the keyway in fence assembly lines up with the key on the fence mount.13. Once fence is in place, slide the fence lock knob through the 1/2" washer and then through the fence assembly and fence mount. Thread T-nut onto the end of the lock knob. Make sure the tabs on the nut sit in the slot on the fence mount.14. Slide the fence back and fourth to make sure it moves freely. Then lock in place.15. Thread the fence tilt knob into the fence.11. From among the loose parts find the cutter head guard. Remove the pan head screw from the bottom of the guard post.12. Turn the spring-loaded knob 1 turn counterclockwise, looking down through the hole in the infeed table.13. Line the slot in the guard post with the pin in the knob. Slide the post through table and over pin in the knob.14. Reinstall the pan head screw in the bottom of the guard post.1Repair Parts1Repair Parts1Repair Parts1Repair Parts1Size: 3.01 MBPages: 44Language: EnglishOpen manual