Haier hw60-b12866nzp User Manual

Power 

           Automatic Drum Washer 

Operating Instructions 

Models: 

Please read this manual carefully before use. 

Please keep this manual in a safe place for future  

reference. 

Specifications 

This product is classified as 

Class I appliance. Please pay 

attention to electrical safety 

during use.

The diagrams in this manual are 

for illustrative purpose only. In 

consideration of continuous 

product improvement, please 

see the actual product for the 

appearance, color and 

accessories which may be 

inconsistent with those 

described in this manual. We 

hereby apologize for this.

Contents 

1.  Notice before Use 

2.  Safety Precautions 

3.  Precautions for Use 

4.  Preparations before Washing 

5.  Operational Procedure 

6.  Control Panel and Program Description 

7.   Display Screen Description 

8.   Other Functions 

9.   Fault Clearance 

10. Cleaning/Maintenance 

Technology of  

variable frequency drive 

Technology of  

power-down memory 

Technology of  

automatic selection 

Please install and adjust the washer according to the instructions in this  

manual so that you can use it in a correct and safer manner. 

1. Select a proper water tap 

2. Remove the water inlet pipe joint 

The length of front end must be more than 10mm. If the  

end face of water tap outlet is unsmooth, please file it  

smooth to avoid water leakage. 

①

 Press the lower end of locking lever; 

②

 Hold the water inlet pipe, press  

down the slider and remove the water  

inlet pipe joint; 

4. Connect the water inlet pipe 
①

 Press down the slider and insert the  

water pipe into the water inlet pipe joint; 

②

 Hook the water inlet pipe joint with  

the locking lever, then loosen the slider  

until a “poop” is heard. 

5. Connect to the washer 
①

 Ring the nut at the other end of water  

inlet pipe onto the water inlet valve joint; 

②

 Tighten and confirm the nut of water  

inlet pipe in place. 
6. Check the water inlet pipe for good connection 
①

 Check for firm connection; 

②

 After installation, turn on the water tap and  

check for water leakage; 

③

 Before every use of the washer, please check  

for firm connection between the water inlet pipe  

and the water tap; 

④

 Never forcibly bend the water inlet pipe. 

The outlet end of drain pipe must be  

higher than 80cm and the highest point  

must be less than 100cm. To prevent the  

drain pipe from coming off, you may  

secure it to its clamp at the back of washer  

or to the firm holder as shown in the  

figure. 

It is not recommended to extend the drain  

pipe. If the extension pipe exceeds 2.5m  

in length, simultaneous water feeding and  

drainage is likely to occur. Please contact  

our After-sales Service Department for the  

extension of drain pipe. 

Adjustment of the feet 
Be sure to adjust four feet  

to level the washer before  

use. 

3. Install the water inlet pipe joint 

①

 Loosen the nut to the extent that  

approximate 3-4 turns of screw thread are  

exposed; 
②

 Loosen four screws of the water inlet pipe  

joint to the extent that the joint can be ringed  

onto the water tap; 
③

 If the water inlet pipe joint cannot be ringed  

onto the water tap, please remove the bushing  

and install again; 
④

 Turn one of screws to an approximately  

proper position in advance, ring the water inlet  

pipe joint onto the water tap, then evenly  

tighten the remaining three screws in place,  

and finally tighten the nut. 

Water inlet pipe joint 

Locking lever 

Slider 

Water inlet pipe 

Wall 

If the water tap is  

placed against the wall,  

you may turn this screw  

to a proper position in  

advance. 

Bushing 

3-4 turns 

Tally 

Nut 

Locking lever 

fig. 1 

fig. 2 

Note: 

After finishing the adjustment of  

four feet, turn the foot support  

nuts to cling to the shell in order  

to support the washer. 

(Add a proper amount of  

detergent required by washing) 

Pre-wash detergent box 
Main wash detergent box 
Softener and bleach box 

When selecting the pre-wash function or the pre-wash  

program, add detergent into the pre-wash box to pre-wash  

the clothes; 

As for the dosage of detergent, please refer to the  

instructions for detergent. Excessive detergent may result  

in too many bubbles and spill as well as affect its  

dissolution. Special low foaming detergent for drum  

washers shall be used. When washing synthetic or wool  

fabrics, be sure to use special detergent; 

The level of softener or liquid detergent should not be  

higher than the “MAX” mark of a distributor box.  

Concentrated softener or liquid detergent should be diluted  

before being added into a distributor box. 

Table top 

Drain pipe holder 

Main control  

panel 

Front panel 

Inner drum 

Window pad 

Door 

Sight glass 

Foot 

Lower trim 

Filter door 

Table top 

Water inlet valve 

Power cord 

Screw (4 pcs) 

Power plug 
Back cover plate 
Drain pipe clamp 

Drain pipe 

Splash-proof plastic  

plug (4 pcs) 

Shell 

Packaging bolts and accessories are used to  

fix internal components of the washer during  

transport and should be removed before using  

the washer. 

Unscrew packaging bolts and take  

out the back-up block. 

Block the bolt hole with a  

splash-proof plastic plug. 

Please keep such disassembled components  

as packaging bolt and back-up block in a safe  

place for future handling of the washer. 

Water inlet pipe assy  Drain pipe holder 

Rat guard 

Operating 

instructions 

Electrical safety  

prompt: 

Please pay attention to  

electrical safety when  

using the washer. 

Warning sign: The  

contents with this  

sign involve the  

safety of both the  

product and user. Be  

sure to strictly follow  

these instructions,  

otherwise the washer  

may be damaged or  

the user may be  

injured. 

Prohibitory sign: The  

contents with this  

sign indicate the  

behaviors to be  

absolutely prohibited.  

Failure to follow these  

instructions may  

result in damage to  

the washer or  

personal injury. 

1. The plug should be accessible after the washer is  

installed in place. Do not disconnect the plug from the  

socket by pulling the power cord. If the power cord needs to  

be replaced, ask a qualified person or contact our  

After-sales Service Department for replacement. Prevent  

the power cord from being pressed by any foot and from  

such problems as break-off, flattening, etc. 

2. Power supply must use a separate socket, the grounding  

terminal of which must be reliably grounded.  

3. Such overload protective devices as proper fuse must be available at the user’s home.  

And, the ammeter, wires and socket must be able to withstand the current of 10A. 

1. Keep the washer away from any heat source and direct sunlight to prevent aging of plastic/rubber 

parts.

1. Do not use such chemicals as flammable detergent and dry-cleaning  

solvent to wash the clothes. Do not use any organic solvent or corrosive  

liquid to wipe the exterior and rubber parts of the washer. Do not use any  

flammable spray near the washer. In case of flammable gas leakage, do  

not plug in or unplug the washer. Do not use the washer near the  

environment with flammable and explosive gas or liquid such as biomass  

pool, etc. 

2. The washer’s door is relatively hot during heating. For the purpose of safety, keep  

children away from the washer. In addition, when draining hot water, be careful to avoid  

scald. 
3. After unpacking the washer, do not allow children to play with the disassembled  

packaging materials such as carton, plastic packaging bag and foam, etc. 
4. Do not install the washer outdoors and in excessively humid environment, otherwise  

the moisture on electrical components may easily cause damage to the ignition system  

or other accidents. In case of inadvertent water spray onto or into the washer, only after  

the washer thoroughly dries can you use it. 
5. Neither place the washer directly on airproof carpet to prevent its bottom vent from  

being blocked nor close up to a wall or furniture to avoid accidents. Do not use the  

washer on any platform higher than the floor, otherwise it may fall off onto the floor and  

be damaged. 

1. Due to fluctuation of water pressure, please check all the joints of water inlet pipe, water tap and  

drain pipe for firm connection before washing every time. In case of loose water pipe connection or  

water leakage, please turn off the water tap and take proper measures or contact our After-sales  

Service Department for reconnection. Only after such faults are cleared can you use it again. 

2. Using the washer at 0 ℃ and below may damage the water inlet valve and drainage system. If the  

washer is stored at 0 ℃  and below, be sure to move and leave it in the environment at room  

temperature for 2-4 hours before use. 

3. It is recommended that the washer be installed in a location with floor drainer. 

4. Do not place any heavy object, heat-producing appliance and item liable to water/liquid leakage to  

avoid the deformation of table top and plastic parts. 

5. Do not wash such waterproof articles as raincoat, bicycle cover and down products as well as  

carpet to avoid abnormal vibration or the damage to articles. 

6. If a brassiere with steel wire is washed in the washer, the steel wire may bounce out. Therefore, do  

not wash any brassiere with steel wire in order to protect the washer. 

7. Do not put the clothes tainted with chemicals into the washer. 

8. Do not open any detergent distributor box during the program operation to avoid some detergent  

leaving in the box. 

9. The washer’s door is equipped with self-lock safety device. Only when the washer is in safe state  

(the water level is below the lower edge of sight glass, the temperature inside the drum is below 50 ℃ , 

the inner drum is not rotating) can you unlock the door. Never forcibly open the door before the washer  

reaches the safe state to avoid damage to the door or scald. “Click” will be heard when opening the  

door. It is normal and arises from the working principle of electromagnetic lock’s internal structure. 

10. Cut off the water supply and power supply after finishing washing every time. Moreover, clean the  

sight glass window pad interlining to prevent contaminants from tainting the clothes again or the  

surface of window pad from going moldy. 

11. When the washer is not in use, please keep the door slightly open to avoid unpleasant smell. Do  

not cover the washer with a plastic bag to avoid moisture staying in the washer. 

12. If the washer is feed water from a water tank and the difference  

between the lowest height of water level in the water tank and the highest height of washer (table top)  

is 0.1~0.5m, put a proper amount of detergent along with the clothes into the washer’s inner drum or  

dilute the detergent and add it in the washer through corresponding detergent before washing to  

prevent it from staying in the washer and affecting the washing and rinsing effect. It is not  

recommended to select the prewash function and add softener in the washer in the above-mentioned  

situations. 

13. Washing capacity 

Check the clothes for special washing  

requirements and make sure that the clothes are  

suitable for washing with a washing machine and  

water in order to avoid the deformation and  

damage of the clothes. 
For the clothes tainted with much mud  

and dust, please remove them before  

washing. 
Wash those clothes liable to color fading  

separately from other clothes. 
Check pockets and remove coins,  

sand, hairpin and other things  

from them. 

To avoid the sound from buttons,  

please turn those clothes with  

buttons inside out before putting  

them into the washer. 
Please unfold and fluff out the clothes before  

putting them into the washer. Furthermore, do  

not overload the washer. 
When washing small articles (e.g. handkerchief,  

gloves and socks, etc.) and those clothes liable  

to intertwist and wear, please put them into net  

bags for washing, rinsing and spinning to prevent  

them from falling between the inner drum and  

window pad and further avoid incomplete  

washing or damage to top-grade clothes. The  

weight of articles in each net bag should not  

exceed 300g and the net bags should not be  

washed together with those clothes not in a net  

bag, otherwise the washer will not be balanced,  

resulting in abnormal vibration. 

Tie the ties, buckle the buttons, zip the zippers  

and sew the openings. 

Connect the water  

inlet pipe and turn  

on the water tap 

Insert the power  

plug into a power  

socket. 

Put down the  

drain pipe. 

Turn on the  

power 

switch. 

Select the desired  

program. 

The “Delay” program is off by default.  

To activate this program, press the  

“Delay” button to make settings. 

Start the selected  

program. 

Select the washing temperature, spinning speed,  

“Delay” function, times of extra rinse and  

“Intense” function, etc. as required. 

Open the door, put the clothes into the washer and  

close the door. Then add a proper amount of detergent  

into corresponding distributor box and close it (refer to  

the section of “Distributor Boxes” under “Notice before  

Use” for details). 

After finishing washing, the washer will automatically switch off. 

HW60-B12866NZP

220-240V/50H 

z 

Power supply 

Water inlet pressure 

Rated washing capacity 

Rated spinning capacity 

Spinning speed 

Washing noise 

Spinning noise 

Fadeless 

cotton fabric 

Wool fabric 

Terylen fabric/blend  

fabric/chemical fiber fabric 

6 kg 

3kg 

1kg 

1200r/m
50dB (A weighted)
68dB (A weighted)

6.0kg
6.0kg

time

time

S-D Inverter

 

445mm

510mm

940mm

Felt

1. Remove the adhesive from the back side of the felt and paste 

    the felt onto the back side of the protection board in a 

    symmetrical position to the board’s corners;

2. Incline the washer backwards and remove fourfeet(Fig.1);

3. Place the side with dimpled grain of rat guard inwards, then 

    pass foot bolts through four holesand tighten them to fix the rat 

    guard to the shell(Fig. 2) and finally level the washer.