Canon mf3220, mf3228, mf3240 Service Manual
Chapter 5
5-1
5.1 Measurement and Adjustment
5.1.1 Basic Adjustments
5.1.1.1 Items of Adjustment
0012-0959
The machine does not have items that are cited for adjustment.
5.2 Service Tools
5.2.1 Special Tools
0012-0989
T-5-1
5.3 Error Code
5.3.1 Outline
5.3.1.1 Error Code Outline
0012-1063
An error code is used to indicate a fault in a machine, and is indicated in the
machine's LCD, showing the nature (symptoms) of the fault. Using the error
code, the service man can readily find out how to correct the fault by simply
referring to the service manual.
An error code may be either of the following two types:
Service Error Codes
If a fault calls for a service man for correction, it is indicated as a
service man error code in the form of "SYSTEM ERROR E+number."
5.3.1.2 Error Code
0012-6035
System error code
T-5-2
Scanner error code
T-5-3
Printer error code
T-5-4
Communication error code
T-5-5
Tool
Description
Parts No.
Grease (MOLYKOTE EM-50L)
Apply to specified areas.
HY9-0007
Grease (MOLYKOTE EMD-110)
Apply to specified areas.
HY9-0023
Grease (IF-20)
Apply to specified areas.
CK-8006
Grease (MOLYKOTE 41)
Apply to specified areas.
CK-8007
Error
code
Major cause/detection
Remedy
E198
Flash ROM write error.
- Turn the power OFF and then back ON..
- Replace the SCNT board.
- Replace the SCNT board.
E674
Modem error.
- Turn the power OFF and then back ON..
- Replace the SCNT board.
- Replace the SCNT board.
Error
code
Major cause/detection
Remedy
E225
CIS lamp has a fault.
- Turn the power OFF and then back ON..
- Replase the CIS unit.
- Replase the CIS unit.
Error
code
Major cause/detection
Remedy
E000
The thermistor has an open circuit or
a short circuit.
a short circuit.
- Check the connector of the fixing film unit.
- Replace the fixing film unit.
- Replace the High-voltage power supply board.
- Replace the DCNT board.
- Replace the fixing film unit.
- Replace the High-voltage power supply board.
- Replace the DCNT board.
The heater has an open circuit. The
thermal fuse has blown.
The High-voltage power supply board
has a fault.
The DCNT board has a fault.
thermal fuse has blown.
The High-voltage power supply board
has a fault.
The DCNT board has a fault.
E100
The scanner assembly has a fault.
- Check the connector of the laser scanner assembly.
- Replace the laser scanner assembly.
- Replace the engine controller PCB.
- Replace the laser scanner assembly.
- Replace the engine controller PCB.
Error Code
Description
0001
Nothing G3 signal received within 35 sec.
0003
Received DIS after sending DIS signal
0004
Received DCN after sending DTC signal
0009
Can't receive any signal within 35 sec. in manual polling mode.
0010
Received DCN signal after sending DTC signal in Polling Rx.
0011
Can't receive any correct response after sending DTC signal.
0012
Remote side Password not match in Polling Rx/our side no any file to be polling.
0013
Can't receive carrier within 6 sec. after sending CFR in date phase C.
0014
Can't receive T.30 signal after sending FTT signal.
0016
Receive DCN signal after sending PTT signal.
0017
Can't receive any response from remote side after sending DIS
0018
Can't detect energy within 6 sec after sending FTT command
0019
Received DCN signal sending CFR signal
001A
No energy on line over 6 sec. within phase C before any corrected ECM frame.
001D
Can't detect flag after sending CFR signal
001E
Timeout in V.17 ECM Rx phase C
0020
Can't correct frame within 6 sec at phase C.
0021
File full.
0022
Owing to noise interference on the line, receiving side can't receive correct data within specified
time (no ECM)
time (no ECM)
0023
Can't receive correct signal after sending CFR signal