Samsung UH55F-E Quick Setup Guide
Quick Setup Guide
The colour and the appearance may differ depending on the product, and the specifications are
subject to change without prior notice to improve the performance.
Download the user manual from the website for further details.
http://www.samsung.com/displaysolutions
UH55F-E
BN68-07851H-00
The terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI Logo are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other countries.
Reverse Side
IR
OUT
CONTR
OL
IN
DP
IN
HDMI
IN
1
HDMI IN 2
DVI IN
(MA
GICINF
GICINF
O)
RGB IN
U
SB
DP
OUT
(L
OOPOUT
)
IN
OUT
RS
232
C
C
IN
OUT
AUDIO
RJ4
5
1
Receives the remote control signal via the external sensor
board and outputs the signal via LOOP OUT.
2
Supplies power to the external sensor board or receives the
light sensor signal.
3
DVI IN: Connects to a source device using a DVI cable or HDMI-DVI
cable.
MAGICINFO: To use MagicInfo, make sure to connect the DP-DVI
cable.
4
Connects to a source device using an HDMI cable.
5
Connects to a PC using a DP cable.
6
Connects to a source device using a D-SUB cable.
7
Connects to another product using a DP cable.
8
Receives sound from a PC via an audio cable.
9
Connects to the audio of a source device.
0
Connects to MDC using an RS232C adapter.
!
Connect to a USB memory device.
(Only for update purpose)
@
Connects to MDC using a LAN cable.
Issues
Solutions
The screen keeps
switching on and off.
Check the cable connection between the
product and PC, and ensure the connection
is secure.
No Signal is displayed
on the screen.
Check that the product is connected
correctly with a cable.
Check that the device connected to the
Check that the device connected to the
product is powered on.
Not Optimum Mode is
displayed.
This message is displayed when a
signal from the graphics card exceeds
the product’s maximum resolution and
frequency.
Refer to the Standard Signal Mode Table and
Refer to the Standard Signal Mode Table and
set the maximum resolution and frequency
according to the product specifications.
The images on the
screen look distorted.
Check the cable connection to the product.
The screen is not clear.
The screen is blurry.
Adjust Coarse and Fine.
Remove any accessories (video extension
Remove any accessories (video extension
cable, etc) and try again.
Set the resolution and frequency to the
Set the resolution and frequency to the
recommended level.
The screen appears
unstable and shaky.
Check that the resolution and frequency of
the PC and graphics card are set within a
range compatible with the product. Then,
change the screen settings if required by
referring to the Additional Information on
the product menu and the Standard Signal
Mode Table.
There are shadows or
ghost images left on
the screen.
Issues
Solutions
The screen is too bright.
The screen is too dark. Adjust Brightness and Contrast.
White does not really
White does not really
look white.
Go to Picture and adjust the White Balance
settings.
The product will turn
off automatically.
Go to System and make sure Sleep Timer is
set to Off.
If a PC is connected to the product, check
If a PC is connected to the product, check
the power status of the PC.
Make sure the power cable is connected
Make sure the power cable is connected
properly to the product and power outlet.
If the signal from a connected device is not
If the signal from a connected device is not
detected, the product automatically turns
off after 10 to 15 minutes.
There is no sound.
Check the connection of the audio cable or
adjust the volume.
Check the volume.
Check the volume.
The volume is too low. Adjust the volume.
If the volume is still low after turning it up
to the maximum level, adjust the volume on
your PC sound card or software programme.
The remote control
does not work.
Make sure that the batteries are correctly in
place (+/-).
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs
switched on in the vicinity.
Troubleshooting Guide
Checking the Components
External sensor KIT
1
Remote Control Sensor
Aim the remote control towards this spot on the LCD Display.
- Keep the area between the remote sensor and remote
control obstacle-free.
2
Light sensor
Automatically detects the intensity of ambient light around a
selected display and adjusts the screen brightness.
3
Power indicator
The power indicator will turn off when the product is turned on.
It will blink in power-saving mode.
4
POWER button
Use this button for turning the LCD Display on and off.
5
SOURCE button
Switches from PC mode to Video mode.
Selects the input source that an external device is connected to.
- Contact the vendor where you purchased the product if any
components are missing.
- The pictures may look different from the actual components.
1
2
3
4
5
6
7
8
9
0
9
0
!
@
@
1
2
3
4
5
Quick Setup Guide
Warranty card
(Not available in some
locations)
MagicInfo Software
DVD
Power cord
Batteries
(Not available in some
locations)
Remote Control
DP cable
RS232C(IN) adapter
Holder-Ring (4EA) /
Screw (4EA)
UH55F-E_INDIA_QSG_BN68-07851H-00.indd 1
2016-10-05 오후 5:59:27