Samsung UD55E-A Quick Setup Guide
Quick Setup Guide
The colour and the appearance may differ depending on the product, and the specifications are
subject to change without prior notice to improve the performance.
Download the user manual from the website for further details.
http://www.samsung.com/displaysolutions
subject to change without prior notice to improve the performance.
Download the user manual from the website for further details.
http://www.samsung.com/displaysolutions
UD46E-A UD46E-C UD46E-B
UD55E-B
BN68-07319J-
0
3
The terms HDMI and HDMI High-Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing
LLC in the United States and other countries.
HDMI Logo are trademarks or registered trademarks of HDMI Licensing
LLC in the United States and other countries.
Reverse Side
IR
OUT
CONTROL
IN
DP
IN
IN
HDMI IN 1
HDMI IN 2
DVI IN
(MAGICINFO)
RGB IN
USB
DP
OUT
OUT
(LOOPOUT)
IN
OUT
RS232C
IN
OUT
AUDIO
RJ45
1
Receives the remote control signal via the external sensor board
and outputs the signal via LOOP OUT.
and outputs the signal via LOOP OUT.
2
Supplies power to the external sensor board or receives the light
sensor signal.
sensor signal.
3
DVI IN: Connects to a source device using a DVI cable or HDMI-DVI cable.
MAGICINFO: To use MagicInfo, make sure to connect the DP-DVI cable.
MAGICINFO: To use MagicInfo, make sure to connect the DP-DVI cable.
4
Connects to a source device using an HDMI cable.
5
Connects to a PC using a DP cable.
6
Connects to a source device using a D-SUB cable.
7
Connects to another product using a DP cable.
8
Receives sound from a PC via an audio cable.
9
Connects to the audio of a source device.
0
Connects to MDC using an RS232C adapter.
!
Connect to a USB memory device. (Only for update purpose)
@
Connects to MDC using a LAN cable.
Issues
Solutions
The screen keeps
switching on and off.
switching on and off.
Check the cable connection between the product
and PC, and ensure the connection is secure.
and PC, and ensure the connection is secure.
No Signal is displayed
on the screen.
on the screen.
Check that the product is connected correctly
with a cable.
Check that the device connected to the
product is powered on.
with a cable.
Check that the device connected to the
product is powered on.
Not Optimum Mode is
displayed.
displayed.
This message is displayed when a signal
from the graphics card exceeds the product’s
maximum resolution and frequency.
Refer to the Standard Signal Mode Table and
set the maximum resolution and frequency
according to the product specifications.
from the graphics card exceeds the product’s
maximum resolution and frequency.
Refer to the Standard Signal Mode Table and
set the maximum resolution and frequency
according to the product specifications.
The images on the
screen look distorted.
screen look distorted.
Check the cable connection to the product.
The screen is not clear.
The screen is blurry.
The screen is blurry.
Adjust Coarse and Fine.
Remove any accessories (video extension
cable, etc) and try again.
Set the resolution and frequency to the
recommended level.
Remove any accessories (video extension
cable, etc) and try again.
Set the resolution and frequency to the
recommended level.
The screen appears
unstable and shaky.
unstable and shaky.
Check that the resolution and frequency of the
PC and graphics card are set within a range
compatible with the product. Then, change the
screen settings if required by referring to the
Additional Information on the product menu
and the Standard Signal Mode Table.
PC and graphics card are set within a range
compatible with the product. Then, change the
screen settings if required by referring to the
Additional Information on the product menu
and the Standard Signal Mode Table.
There are shadows or
ghost images left on the
screen.
ghost images left on the
screen.
The screen is too bright.
The screen is too dark.
The screen is too dark.
Adjust Brightness and Contrast.
Issues
Solutions
White does not really
look white.
look white.
Go to Picture and adjust the White Balance
settings.
settings.
The product will turn off
automatically.
automatically.
Go to System and make sure Sleep Timer is
set to Off.
If a PC is connected to the product, check the
power status of the PC.
Make sure the power cable is connected
properly to the product and power outlet.
If the signal from a connected device is not
detected, the product automatically turns off
after 10 to 15 minutes.
set to Off.
If a PC is connected to the product, check the
power status of the PC.
Make sure the power cable is connected
properly to the product and power outlet.
If the signal from a connected device is not
detected, the product automatically turns off
after 10 to 15 minutes.
There is no sound.
Check the connection of the audio cable or
adjust the volume.
Check the volume.
adjust the volume.
Check the volume.
The volume is too low.
Adjust the volume.
If the volume is still low after turning it up to
the maximum level, adjust the volume on
your PC sound card or software programme.
the maximum level, adjust the volume on
your PC sound card or software programme.
The remote control does
not work.
not work.
Make sure that the batteries are correctly in
place (+/-).
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is connected.
place (+/-).
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs
switched on in the vicinity.
switched on in the vicinity.
Troubleshooting Guide
Checking the Components
External sensor KIT
108&3
ON
1
Aim the remote control towards this spot on the LCD Display.
- Keep the area between the remote sensor and remote control
- Keep the area between the remote sensor and remote control
obstacle-free.
2
Automatically detects the intensity of ambient light around a
selected display and adjusts the screen brightness.
3
The power indicator will turn off when the product is turned on.
It will blink in power-saving mode.
It will blink in power-saving mode.
4
Use this button for turning the LCD Display on and off.
5
Switches from PC mode to Video mode.
Selects the input source that an external device is connected to.
Selects the input source that an external device is connected to.
- Contact the vendor where you purchased the product if any components
are missing.
- The pictures may look different from the actual components.
1
2
3
4
5
6
7
8
9
0
9
0
!
@
@
1
2
3
4
5
Quick Setup Guide
Warranty card
(Not available in some
locations)
Regulatory guide
+
+
-
-
MagicInfo Software
DVD
Power cord
Batteries
(Not available in some
locations)
Remote Control
DP cable
RS232C(IN) adapter
AUDIO adapter
Holder-Ring (4EA) /
Screw (4EA)
[UDE-A,B,C-QSG-INDIA]BN68-07319J-03.indd 1
2015-08-20 9:46:39